- How To Change Bios Settings
- Bios Settings For Pcie Enumeration Delay
- Bios Settings For Macbook Pro
- Bios Settings For Memory
How to Change BIOS or UEFI Firmware Settings. The actual BIOS or UEFI settings screen looks different on different PC models. PCs with a BIOS will have a text-mode interface you can navigate with your arrow keys, using the Enter key to select options. You’ll see the keys you can use spelled out at the bottom of the screen.
The Mac does not have a BIOS to enter. The equivalent would be the Extensible Firmware Interface (EFI) to access this (which is traditionally referred to as Open Firmware hence the O and F key. Boot OS X, Windows, and Linux on Mac or PC with UEFI or BIOS firmware. Download the latest Clover package from the Getting Started section to begin. From there you need to follow the steps on the installer but use the Customise option to correctly install for your System. Use the settings below, UEFI Motherboard Settings. Install Clover for. The settings stored in NVRAM depend on your Mac and the devices that you're using with your Mac. If you experience issues related to these settings or others, resetting NVRAM might help. For example, if your Mac starts up from a disk other than the one selected in Startup Disk preferences, or a question mark icon briefly appears before your Mac. Hello, I have buyed a lot of Dell Precision 490 (for my company), and I want install Linux on them with an automatic tool. This tool is based on the MAC Address of the pc. And I do not found the ethernet address of the NIC with BIOS Setup (Information field does not give it). Could you help me.
You will find this post useful in case you are looking for a way to make your computer boot from a USB drive, instead of booting from hard drive as it normally does. In this post you will be learning the steps to enable USB boot in BIOS settings, so that you can make your computer boot up from a Windows recovery drive.
Enable USB Boot in BIOS
In general, most computers boot from their hard drives where the computers operating system is stored. While some newer computers may provide a choice for booting from the USB drive during startup, others may not do so.
Follow the steps below to check whether your computer can boot from a USB drive and make it boot from a USB drive, in case it is not set that way.
1. Plug a Bootable USB Drive into the USB port of your computer.
Note: You can skip steps 1 ~ 4 and start from step 5 in case you are certain that your computer is not set up to boot from a USB drive.
2. Remove all other portable media like CD, DVD from the computer and power it on.
3. If the computer is configured to automatically boot from the USB drive, you will see a screen that says “Automatic boot in 10 seconds…”
4. If you believe the computer is trying to boot from the hard drive, you’ll need to manually configure it to boot from the USB drive.
5. Wait for a safe point where you can reboot the computer.
6. Reboot the computer and watch the screen for instructions on which key to press for getting into the boot device selection menu, or “BIOS setup”.
The screen messages will say something like Press [XXX Key] to Enter Setup or BIOS SETUP. You will only have a few seconds to read the instructions on your screen. Reboot the computer again, in case you missed the opportunity to read the instructions properly.
7. Use the suggested Key to get into BIOS settings
Please note that you may need to press the suggested key more than once to enter BIOS. You should not hold down the key (just press and release). Also, do not press the key too many times as you may end up locking the system or
generating system errors.
generating system errors.
8. Go to the Boot Tab of BIOS setup utility and use the keys to make your computer boot from the USB drive first in the boot sequence.
Note: In general, the BIOS on most computers will list the USB boot option as Removable Devices or USB. However, on some computers USB boot option might be listed under Hard Drive. Make sure to check under hard drive option, in case you are having problems locating the USB boot option.
How To Change Bios Settings
9. Save the changes and exit from BIOS utility.
10. Your computer is now ready to boot from USB drive
When you enable boot from a a USB device, what you are essentially trying to do is to make your computer run from the operating system that is installed on the USB device, instead of running from OS installed on the hard drive.
For computers using Windows operating system you can easily create a Bootable Windows USB drive or a Windows USB Recovery Drive. These will allow you to boot a computer from the USB drive whenever your Windows computer is facing problems and requires troubleshooting.
If you are bored of your old windows pc, the Crotona, the same old UI, the blue screen of death. Then you are at the correct place, I have created a video on YouTube in which I showed you a step by step tutorial on how to install mackintosh on your non mac pc or in my case an AMD computer if you want to watch that video I will link it right over here, for now I will include the important links that we need while installing the macOS on our AMD computer
My Pc specification for AMD Sierra
Processor – AMD Fx-6300 Black Edition 6 cores
Ram – 4 GB
Motherboard – GIGABYTE GA78LMT-USB3
Graphics Card – NVIDIA GTX 750 Ti
1) Checking for the compatibility
Not a whole lot of processors especially the AMD ones are compatible with the hackintosh Operating system but thankfully we have a website from where we can find out the compatibility of the processor to check just visit http://cpuboss.com/ and search for your processor (mine is the FX-6300 6 cores black edition) scroll down to features and if your CPU is compatible you will get a 1 instruction set if it is there then follow the rest of the guide if not then you cannot install the Sierra.
2) Downloading the Python Installer
If you are using the cmd method to download the dmg file and creating a bootable usb for your hackintosh machine then you will have to install the latest python drivers on your pc , you can download then from here – https://www.python.org/
3) Downloading the Sierra (dmg) file
Links to download the Sierra (12.16.4) this is the same one that i used in the video
– SierraAMDv5.2 – http://bit.ly/2qJ2vLb
4) Making the USB boot-able
You will have to download TransMac software this will make the pen-drive bootable with the macOS, this will also make the pendrive format into the GUID format which is readable by macOS.
Link to download the software – https://www.acutesystems.com/scrtm.htm
5) Changing the Bios Settings
There are a lot of tweaks that you can do to make the installation smoother but basically you will only need to make this one change
INTEGRATED PERIPHERALS – ON CHIP SATA TYPE – AHCI
this is basically it if you want then you can disable or enable the 3.0 USB hubs if you want but that is not mandatory
6) Boot Arguments
Bios Settings For Pcie Enumeration Delay
![Credential Credential](/uploads/1/1/8/7/118747044/495388437.jpg)
You will have to add the following boot arguments while installing the macOS,
please note – you will have to change it later when you have installed the macOS and installed the clover bootloader
boot arguments = ncpi=0x3000 -v nv_disable=1
7) Installing NVIDIA Web Drivers
Bios Settings For Macbook Pro
to install web drivers you will have to download the necessary web drivers for your graphic card mine is the NVIDIA GTX 750TI
Bios Settings For Memory
Link – https://www.tonymacx86.com/nvidia-drivers/
add the following command ( this is enable the graphic card, we previously stopped them in step 6)
nvda_drv=1
That’s all folks !